Spud Guns

	Sign In Sign-Up

Home Page
disclaimer
Spud Guns
Missle Launchers
Tennis Ball Cannon
Projectile Launcher
Guestbook
Links
Photo Page

How to make a Spud Gun *So.... you wanna shoot some sht up** Your probly thinkin to yourself a spud guns probly hard as sht to make but its not, my stupid ass sister could make this sht. Plus i know what i am doin, i aint one of those kids who takes instuctions off somone elses site and says i have made this sh*t. I WILL NOT put instructions on this site for a product that i have not already made. Thats my promise!!! Plus if you dont know how or have problems with anything on this site email me and i will explain it to you as best i can.
DUHHH is that a spud gun noooo....thats my moms dildo			Supplies -3" pvc piping-->you'll only need about a foot of this -1 1/2" pvc piping-->this differs the longer the pipe the farther the potato will go -cup adapter-->this adaps 1 1/2" pipe to a 3" pipe -3" pipe ender-->if you dont know what this is get off my site -3 way pipe adapter-->this is hard to explain your gonna have to look at the foto of my spud gun. but it connects two 3" pipes together and has a small 1 " pipe in the middle, thats for the hair spray. -1" pipe screw on ender-->thats for the hairspray pipe -PVC Cement--> acts as glue for gluing the pipes together regular glue will not work unless you wanna blow off your hand -Colman lantern igniter-->these are simply a spark maker, you twist at the top and sparks come out the bottom
Instructions first start off by sawing the 3" piping into two separate pieces each piece measuring about 4". set these peaces aside and take your barrel and glue it into the cup adaptor, set that aside also so it can dry. Now look at your grill igniter it should have two bolts on either side between the the twist part and the sparker you will need these so that you can bolt the igniter onto the pipe. now drill a hole into the three way pipe adapter so it is the same size as the screw threading so it will be a tight fit. Remember drill this hole as far away form the hairspay hole as possible because if you spray the the igniter with the hairspray it will not spark. You may need too also drill a larger hole on the top of the other one because the igniter gives you very little room on the threading to bolt to the pipe. Also remember it only needs to be deep enough so you can screw the bolt on to it. if it is too deep it may cause it to leak, or even blow out. Once you have screwed on the bolts you will need to glue the igniter to the pipe to block up any air holes, dont use the pvc cement instead use a glue gun or some kind of silicon glue. Make sure it can withstand heat. Give that time to dry now simply glue the two peices of the 3" piping to the 3 way adaptor(the one with the igniter)then on each side of that glue the cup adaptor and the ender and you got your self a f*ckin spud gun			procedure for shooting this gun to shoot this gun all you need is hairspray, potatos, and a ram rod. it would be a good idea to sand a sharp edge on the top of the barrel so the potato is skinned to the exact size of the barrel as it is slid down it. once the potato is in the barrel you need to ram it down at the bottom of the barrel with the ram rode. the potato should sit rite above the cup adaptor. now screw off the top of the 1" hairspray hole and spray about 3-4 seconds of hairspray into the explosion chamber and cap it off. Then aim it at a safe target and twist the igniter and watch the sh*t fly. Somthing fun to do with this is put a couple paintballs, marbles, bbs down the barrol and buck shoot it. also try putting nails into the potato for an effective death dart. i do not recommend even shooting this it is only a expensive "paperwieght"!!!!